You Are Here: Home » Router » -Router Cisco
FRM – 92095: Oracle JInitiator version too low. Please install version 1.1.8.2 or higher

FRM – 92095: Oracle JInitiator version too low. Please install version 1.1.8.2 or higher

Jika anda menggunakan MAC OS X, apakah anda pernah mendapatkan pesan error pada saat ingin mengakses sebuah web berbasis Java? Pesannya adalah sebagai berikut : "FRM - 92095: Oracl ...

smart city pariaman kota

smart city pariaman kota

smart city pariama  kota ...

Link backbone Mentawai

Link backbone Mentawai

untuk optimalisasi trafik ke mentawai telkom meningkatkan layanannya dengan mengupgrade bacbone dari vsat scpc ke RADIO CERAGON. Hop radio dari bukittinggi ke mentawai ME-D1-BKTA-- ...

Mini ring unand  using omni switch and L3 HP dengan metro satu metro dengan 2 port beda

Mini ring unand using omni switch and L3 HP dengan metro satu metro dengan 2 port beda

ini di karenakan link nya menjadi prioritas karena kampus ini makai bw nya cuku gede. yah alih2 ini untuk meminimalkan ggnnya. yah supaya pelanggan puas. bikin 2 homing transport : ...

Osi Layer and TCPIP

Osi Layer and TCPIP

      Switching concept   ...

Cisco 28XXX

  XXXXXXXXX#show run Building configuration... Current configuration : 1136 bytes ! ! No configuration change since last restart ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname¬†XXXXXXX boot-start-marker boot-end-marker ! enable secret 5 $1$M5N4$vw6hT79XRuF9y0y.7XkYh1 ! no aaa new-model ! resource policy ! ip cef ! ! ! ...

Read more

* ADSL over Ethernet. The ADSL modem will be acting as bridge, and the router CE will make a call via its Ethernet port. Have a try !!!!

RouterX#sh run Building configuration... Current configuration : 1480 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RouterX ! boot-start-marker boot-end-marker ! enable secret 5 $1$OGqn$WnmL8LrQMH6gRxNzTiqTk1 enable password cisco ! no aaa new-model ! resource policy ! no network-clock-participate slot 1 no network- ...

Read more

Layer 2 Tunneling Protocol L2TP

L2TP extends the PPP model by allowing the L2 termination point (Network Access Server or LAC L2TP Access Concentrator) and PPP endpoint (LNS L2TP Network Server) to reside on different devices interconnected by an IP network. L2TP uses UDP port 1701. Operation There are two steps to tunneling a PPP session with L2TP- 1) establishing a Control Connection for a Tunnel, and 2) establishing a Session as trigge ...

Read more

PPP over Ethernet

PPP over Ethernet (PPPoE) provides the ability to connect a network of hosts to a Remote Access Server RAS (also called as Network Access Server NAS or Broadband Remote Access Server B-RAS). With this model, each host (or a CPE) utilizes it's own PPP stack. This way access control, billing and type-of-service can be done on a per-user basis. To establish a point-to-point connection over Ethernet, each PPP s ...

Read more

PPP Authentication: CHAP

The Challenge Handshake Authentication Protocol (CHAP) (protocol value= 0xC223) is used to verify the identity of the peer using a 3-way handshake. After the Link Establishment Phase is complete, the authenticator sends a "Challenge" message to the peer containing a value. The peer responds with a "Response" message containing a hash-value obtained after performing MD5 on the value sent in the Challenge mes ...

Read more

PPP Authentication: PAP

RFC 1334 discusses PPP authentication protocols. The Password Authentication Protocol (PAP) (protocol value=0xC023) is one of two authentication methods available for PPP. PAP uses 2-way handshake to establish its identity with its peer. The Authentication Phase is optional in PPP. This phase starts after Link Establishment Phase is successfully completed. After Link Establishment Phase is complete, the use ...

Read more

IPv6 & IPv4 over PPP

In order to establish communication over a point-to-point link, each end of the point-to-point link first sends LCP packet to configure and test the data-link. After the link has been established and optional facilities are negotiated for LCP, PPP sends NCP packets to choose and configure one or more Network Layer protocols. Once each of the chosen network layer protocols have been configured, datagrams fro ...

Read more

Understanding PPP

RFC 1661 describes PPP in detail. PPP provides a standard method of transporting multi-protocol datagrams over point-to-point links. PPP has three main components- A way of encapsulating multi-protocol datagrams A Link Control Protocol (LCP) for establishing, configuring & testing data-link connection. A family of Network Control Protocols (NCPs) for establishing & configuring different network-laye ...

Read more

Class Selector DSCP Values

The Class Selector (CS) DSCP values provide backward compatibility with IP Precedence. By examining the first 3 bits in each binary DSCP value in the following table, these 8 DSCP values match 8 different values that can be encoded in the 3-bit IP Precedence field.  Name of DSCP Class Selector  Binary Value of DSCP  Equivalent IP Precedence Value  Default  0 0 0 0 0 0 0  CS1 0 0 1 0 0 0  1 CS2 0 1 0 0 0 0   ...

Read more

Assured Forwarding and Expedited Forwarding

The Assured Forwarding (AF) PHB contains two separate QoS functions. The first function is Queueing. Each router classifies the packets into 4 different classes, and packets from each classes are placed in seperate queues. The AF PHB does not guarantee that each packet will be delivered and it also does not reserve any minimum bandwidth for each class. The second function defines Congestion Avoidance. RFC 2 ...

Read more

© 2011 Powered By Wordpress, Goodnews Theme By Geeks Docuementation

Scroll to top