You Are Here: Home » Router (Page 3)

All Router

FRM – 92095: Oracle JInitiator version too low. Please install version 1.1.8.2 or higher

FRM – 92095: Oracle JInitiator version too low. Please install version 1.1.8.2 or higher

Jika anda menggunakan MAC OS X, apakah anda pernah mendapatkan pesan error pada saat ingin mengakses sebuah web berbasis Java? Pesannya adalah sebagai berikut : "FRM - 92095: Oracl ...

smart city pariaman kota

smart city pariaman kota

smart city pariama  kota ...

Link backbone Mentawai

Link backbone Mentawai

untuk optimalisasi trafik ke mentawai telkom meningkatkan layanannya dengan mengupgrade bacbone dari vsat scpc ke RADIO CERAGON. Hop radio dari bukittinggi ke mentawai ME-D1-BKTA-- ...

Mini ring unand  using omni switch and L3 HP dengan metro satu metro dengan 2 port beda

Mini ring unand using omni switch and L3 HP dengan metro satu metro dengan 2 port beda

ini di karenakan link nya menjadi prioritas karena kampus ini makai bw nya cuku gede. yah alih2 ini untuk meminimalkan ggnnya. yah supaya pelanggan puas. bikin 2 homing transport : ...

Osi Layer and TCPIP

Osi Layer and TCPIP

      Switching concept   ...

Custom Queuing

Custom Queuing (CQ) is a Congestion Management technique which is round-robin like where frames from each queue are serviced until a byte-counter limit threshold is met. Once this threshold is met, the frames from next queue are serviced. There are 17 queues in CQ- queue 0 is the System Queue while queues 1-16 are user-defined. Queue 0 is used for keepalives, some routing protocols whose traffic is generate ...

Read more

Traffic Shaping

Traffic Shaping involves in queueing traffic rather than dropping it. Traffic Shaping terminology- Tc - Time interval (in milliseconds) over which the committed burst (Bc) can be sent. Tc = Bc/CIR Bc - Committed burst size (in bits). This is the amount of traffic that can be sent over an interval Tc CIR - Committed Information Rate (in bits per second). The rate defined in the traffic contract Shaped Rate - ...

Read more

Traffic Policing

Traffic Policing, like Traffic Shaping, is used to abide by the traffic contract i.e. maintain CIR. The Policer measures the cumulative byte-rate of the packets. The Policer acts on the packet as either allowed to pass, dropped or remarked with a different IP Precedence or IP DSCP value. CB Policing also uses the concept of token bucket; however, there are variations in its operation as compared to CB Shapi ...

Read more

Configuring RIP in JUNOS

Network topology: Here, RIP is enabled between Juniper Networks M10i router and SRX210 Service Gateway. Initial RIP Configuration M10i router: interfaces {     fe-0/3/0 {         unit 0 {             family inet {                 address 172.16.6.10/24;             }         }     }     lo0 {         unit 0 {             family inet {                 address 1.1.1.1/32;             }         }     } } proto ...

Read more

OSPF Designated Router

OSPF elects a Designated Router (DR) for each broadcast network to act as the main point of contact for the network segment. Each router on the segment becomes adjacent with the DR, which handles all LSAs for the network. Each router sends the DR information using the multicast address 224.0.0.6. The DR sends the network LSA (LSA Type 2) to represent the broadcast network to the rest of the OSPF area. To av ...

Read more

NG-mVPN Series – Control Plane

  Contents 1¬†Introduction 1.1¬†Rosen-model limitations 2¬†NG-mVPN Control Plane 2.1¬†Provider Multicast Service Interface (PMSI) 2.2¬†PMSI Tunnel Attribute 2.3¬†Source AS Extended Community 2.4¬†VRF Route Import Extended Community 3¬†mVPN Auto-Discovery - Intra-AS 4¬†mVPN Auto-Discovery - Inter-AS 5¬†C-Multicast Routes 6¬†Using S-PMSI A-D Route 7¬†Summary Introduction This series on NG-mVPN (short for Next-Genera ...

Read more

Multicast VPN – The New Way

The new way refers to the setting up of Multipoint LSP in the MPLS VPN environment to carry multicast traffic in the VPN. Here, all CE routers belong to a single customer at different branches. There is no multicast receiver behind CE3 router. The MPLS core is PIM-free. Only PE routers will run PIM with the CE routers. PE routers configuration The Loopback 0 interface of PE1 router is configured to be used ...

Read more

Multicast VPN (mVPN)

Network Topology: Step 1: Choosing the PIM mode for P-network Here, the SP is running PIM SM using Auto-RP. PE2 router is configured as the RP-Mapping Agent while PE2 and PE3 are configured as Candidate-RPs (C-RPs). PE1, PE2 & PE3 PIM Configuration PE1 router: ip multicast-routing ! interface Loopback 0  ip address 1.1.1.1 255.255.255.255  ip pim sparse-mode ! interface fastethernet 0/0  ip pim sparse-m ...

Read more

OTV Use Case

In this article, I will demonstrate a use case of Overlay Transport Virtualization (OTV) technology from Cisco. As the name suggests, it is an overlay technology which is used to extend Layer 2 networks, usually between data centers. The current implementation is only supported on Cisco Nexus 7000 switches, NX-OS 5.1 and above. In NX-OS 5.1, OTV requires IP Multicast support in the transport network but the ...

Read more

VXLAN

  Introduction ¬† Traditionally, all data centers use VLANs to enforce Layer2 isolation. As data centers grow and needs arise for extending Layer2 networks across data center or may be beyond a data center, the shortcomings of VLANs are evident. These shortcomings are - In a data center, there are requirements of thousands of VLANs to partition traffic in a multi-tenant environment sharing the same L2/L ...

Read more

© 2011 Powered By Wordpress, Goodnews Theme By Geeks Docuementation

Scroll to top