You Are Here: Home » Metro » -Metro Alcactel (Page 2)
FRM – 92095: Oracle JInitiator version too low. Please install version 1.1.8.2 or higher

FRM – 92095: Oracle JInitiator version too low. Please install version 1.1.8.2 or higher

Jika anda menggunakan MAC OS X, apakah anda pernah mendapatkan pesan error pada saat ingin mengakses sebuah web berbasis Java? Pesannya adalah sebagai berikut : "FRM - 92095: Oracl ...

smart city pariaman kota

smart city pariaman kota

smart city pariama  kota ...

Link backbone Mentawai

Link backbone Mentawai

untuk optimalisasi trafik ke mentawai telkom meningkatkan layanannya dengan mengupgrade bacbone dari vsat scpc ke RADIO CERAGON. Hop radio dari bukittinggi ke mentawai ME-D1-BKTA-- ...

Mini ring unand  using omni switch and L3 HP dengan metro satu metro dengan 2 port beda

Mini ring unand using omni switch and L3 HP dengan metro satu metro dengan 2 port beda

ini di karenakan link nya menjadi prioritas karena kampus ini makai bw nya cuku gede. yah alih2 ini untuk meminimalkan ggnnya. yah supaya pelanggan puas. bikin 2 homing transport : ...

Osi Layer and TCPIP

Osi Layer and TCPIP

      Switching concept   ...

OSPF Extensions for MPLS TE

Three new LSAs were defined called¬†Opaque LSAs. Opaque LSA type 9 has a flooding scope limited to local-link. Opaque LSA type 10 has a flooding scope limited to the area (intra-area) and Opaque LSA type 11 has a flooding scope that is autonomous system wide (inter-area like LSA type 5). MPLS TE uses LSA type 10 for intra-area MPLS TE. A new bit was defined¬†‚ÄėO‚Äô¬†in the Options field of OSPF Hello packet heade ...

Read more

MPLS TE Basics

MPLS TE Overview Traditional IP routing is based on forwarding the traffic to the destination as quickly as possible. As a result, the routing protocols find out the shortest path to the destination based on the cost of the link (also called metric) that the packet is forwarded. Further, the IP packets are forwarded on a per-hop basis i.e. every router (hop) forwards the packet based on the destination IP a ...

Read more

Interarea TE tunnels

In MPLS TE Basics article, we examined how link attributes are gathered, how a path is computed based on user-defined constraints and how it is signaled. One of the limitations is that the TE LSP path is computed for single IGP area only due to lack of visibility of the topology in other IGP areas. In OSPF, the ABR hides the topology between two areas. This causes a problem in large networks where multiple ...

Read more

Per-VRF MPLS-TE Tunnels

This is a solution to route traffic from different VRFs to different MPLS-TE tunnels rather than making all VRFs traffic to go through a single MPLS-TE tunnel. Network topology: Since TE tunnels will be configured PE-to-PE, no LDP is required. RSVP-TE will be used to exchange labels. However, LDP must be enabled on MPLS TE tunnels. This is required so that labels can be exchanged for Loopback11 and Loopback ...

Read more

P2MP MPLS TE over DMVPN

This example demonstrates setting up P2MP MPLS TE using RSVP-TE over IP-based DMVPN network. DMVPN Configuration In figure 1, an mGRE tunnel is setup between Hub, Spoke1 and Spoke2 routers. The Hub router acts as the Next-Hop Server (NHS). The address of NHS is manually configured on the Spoke routers. Both Spoke routers (also called Next-Hop Clients NHCs) register their NBMA and Tunnel IP addresses to the ...

Read more

PBB-VPLS

    Introduction   VPLS connects multiple geographically separated customer sites by emulating a bridge domain. All customer sites connected to the same VPLS instance appear to be in the same LAN segment. However, VPLS requires all PE routers be fully meshed with pseudowires. Hierarchical VPLS is often implemented in service provider network to improve scalability as it removes the requirement of pseudowire ...

Read more

Hierarchical VPLS

  Virtual Private LAN Service (VPLS) has become a very attractive technology over the past few years with the advent of MPLS. The reason being some enterprises are very reluctant to relinquish routing control of their network to the service provider and desire L2VPN services with multipoint connectivity. VPLS allows service providers to deploy carrier-class service over Ethernet/MPLS-based network in a real ...

Read more

IEEE 802.1ak – Multiple Registration Protocol

  In PBB-VPLS, for N:1 mode, when an I-VPLS instance receives broadcast/unknown/multicast (BUM) traffic, it is forwarded to all other IB-PE routers as multiple I-VPLS instances share a common B-VPLS instance. The traffic is forwarded to remote IB-PE routers even if they do not have that I-VPLS instance locally bound to the B-VPLS. This causes unnecessary bandwidth waste as the remote IB-PE routers will drop ...

Read more

Routed VPLS

This article is to demonstrate Alcatel-Lucent proprietary solution of Routed VPLS (R-VPLS). It allows a VPLS SAP interface to be configured with a Layer 3 IP address and make the interface route-able. This article will use figure 1 to demonstrate R-VPLS configuration. Figure 1 shows that two servers (Application Server and Database Server) has two direct connections to two ALU 7450 switches - the 7450s run ...

Read more

© 2011 Powered By Wordpress, Goodnews Theme By Geeks Docuementation

Scroll to top