You Are Here: Home » Router » MikroTik Wireless Configuration

MikroTik Wireless Configuration

Setup uses Safe Mode. It means that all changes that are made during setup
are reverted in case of error, or if Ctrl-C is used to abort setup. To keep
changes exit setup using the ‘x’ key.

Choose options by pressing one of the letters in the left column, before
dash. Pressing ‘x’ will exit current menu, pressing Enter key will select the
entry that is marked by an ‘*’. You can abort setup at any time by pressing
Ctrl-C.
Entries marked by ‘+’ are already configured.
Entries marked by ‘-’ cannot be used yet.
Entries marked by ‘X’ cannot be used without installing additional packages.
r – reset all router configuration
+ l – load interface driver
+ a – configure ip address and gateway
d – setup dhcp client
+ s – setup dhcp server
p – setup pppoe client
t – setup pptp client
* x – exit menu
your choice:
OR
[[email protected]] > ip address
[[email protected]] ip address> add address=192.168.1.1/24 interface=ether1
[[email protected]] ip address> pr
# ADDRESS NETWORK BROADCAST INTERFACE
0 192.168.1.1/24 192.168.1.0 192.168.1.255 ether1
[email protected]] ip address> /
[[email protected]] >
[[email protected]] >interface
[[email protected]kroTik] interface> pr

Flags: X – disabled, D – dynamic, R – running
# NAME TYPE RX-RATE TX-RATE MTU
0 X ether1 ether 0 0 1500
1 X wlan1 wlan 0 0 1500
[[email protected]] interface> enable 0
[[email protected]] interface> enable 1

[[email protected]] interface> pr
Flags: X – disabled, D – dynamic, R – running
# NAME TYPE RX-RATE TX-RATE MTU
0 R ether1 ether 0 0 1500
1 X wlan1 wlan 0 0 1500
[[email protected]] ip address>add address=172.1.2.1/30 interface=wlan1
[[email protected]] interface eoip>
[[email protected]] interface eoip
>add name=eoip-tunnel1 remote-address=172.1.2.2 tunnel-id=1 disabled=no arp=enabled
[[email protected]] interface eoip>pr
Flags: X – disabled, R – running
0 R name=”eoip-tunnel1? mtu=1500 mac-address=FE:FD:00:00:00:00 arp=enabled remote-address=172.1.2.2 tunnel-id=1
[[email protected]] interface eoip>..
[[email protected]] interface>
[[email protected]] interface> bridge
[[email protected]] interface bridge>
add name=bridge1
[[email protected]] interface bridge>pr
Flags: X – disabled, R – running
0 R name=”bridge1? mtu=1500 arp=enabled mac-address=00:00:00:00:00:0 forward-protocols=ip,arp,appletalk,ipx,ipv6,other stp=no priority=32768 ageing-time=5m forward-delay=15s garbage-collection-interval=4s hello-time=2s max-message-age=20s
[[email protected]] interface bridge>port
[[email protected]] interface bridge port>pr

# INTERFACE BRIDGE PRIORITY PATH-COST
0 ether1 none 128 10
1 eoip-tunnel1 none 128 10
2 wlan1 none 128 10
[[email protected]] interface bridge port>set eoip-tunnel1 bridge=bridge1
[[email protected]] interface bridge port>set ether1 bridge=bridge1
[[email protected]] interface bridge port>pr
# INTERFACE BRIDGE PRIORITY PATH-COST
0 ether1 bridge1 128 10
1 eoip-tunnel1 bridge1 128 10
3 wlan1 none 128 10
[[email protected]] interface bridge port>.. ..
[[email protected]] interface>wireless
[[email protected]] interface wireless>set wlan1 mode=bridge disable-running-check=no band=5ghz frequency=5180 ssid=test1
Configurration For Mikrotik Station / Client
[[email protected]] interface eoip>add name=eoip-tunnel1 remote-address=172.1.2.1 tunnel-id=1 disabled=no arp=enabled
[[email protected]] interface wireless>set wlan1 mode=station disable-running-check=no band=5ghz frequency=5180 ssid=test1
[[email protected]] interface>pr
Flags: X – disabled, D – dynamic, R – running
# NAME TYPE RX-RATE TX-RATE MTU
0 R ether1 ether 0 0 1500
1 R bridge1 bridge 0 0 1500
2 R eoip-tunnel1 eoip-tunnel 0 0 1500
3 R wlan1 wlan 0 0 1500

About The Author

harrychanputra.web.id

Number of Entries : 295

Leave a Comment

© 2011 Powered By Wordpress, Goodnews Theme By Geeks Docuementation

Scroll to top