You Are Here: Home » Dsl » Dslam » -Dslam Cisco » Command DSLAM CISCO

Command DSLAM CISCO

Command DSLAM CISCO

Table 1-1: Command Modes
Command Mode Access Method Prompt Exit Method
EXEC (user) Log in to the switch or Cisco DSLAM.

DSLAM>

Use the logout command.
Privileged EXEC From user EXEC mode, use the enable command and enter your password.

DSLAM#

To return to user EXEC mode, use the disablecommand.
ROM monitor From privileged EXEC mode, use the reload command. Press Break during the first 60 seconds while the system boots.

rommon x>

The x represents the number of commands that have been entered at the DSLAM prompt. To exit to ROM monitor mode, use the contcommand.
Global configuration From privileged EXEC mode, use the configure command. Use the keyword terminal to enter commands from your terminal.

DSLAM(config)#

To exit to privileged EXEC mode, use the exit or end command or press Ctrl-Z.
Interface configuration From global configuration mode, enter by specifying an interface with the interface command.

DSLAM(config-if)#

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
Profile configuration From global configuration mode, enter by specifying a profile with a dsl-profile command.

DSLAM(cfg-dsl-profile)#

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
Line configuration From global configuration mode, enter by specifying a management interface with a line command.

DSLAM(config-line)#

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
ATM router configuration From global configuration mode, configure the ATM router configuration with the atm router pnni command.

DSLAM(config-atm-router)#

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
PNNI node configuration From ATM router configuration mode, configure the PNNI routing node with the node command.

DSLAM(config-pnni-node)#

To exit to ATM router configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
Auto-sync configuration From global configuration mode, configure redundancy synchronization features with the auto-sync command.

DSLAM(config-auto-sync)

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
Redundancy configuration From global configuration mode, configure additional redundancy options with the redundancy command.

DSLAM(config-red)

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
VRF configuration From global configuration mode, configure a VPN routing/forwarding (VRF) routing table with the ip vrf command.

DSLAM(config-vrf)

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
DHCP pool configuration From global configuration mode, configure the DHCP address pool name and enter DHCP pool configuration mode, with the ip dhcp pool command.

DSLAM(dhcp-config)

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
ATM accounting file configuration From global configuration mode, define an ATM accounting file with the atm accounting file command.

DSLAM(config-acct-file)#

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
ATM accounting selection configuration From global configuration mode, define an ATM accounting selection table entry with the atm accounting selection command.

DSLAM(config-acct-sel)#

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.
ATM E.164 translation table configuration From global configuration mode, enter the atm e164 translation-table command.

DSLAM(config-atm-e164)

To exit to privileged EXECmode, use the exitcommand, the end command, or press Ctrl-Z.
ATM signaling diagnostics configuration From global configuration mode, enter the command atm signalling diagnostics index.

DSLAM(cfg-atmsig-diag)

To exit to global configuration mode, use the exit command.

To exit directly to privileged EXEC mode, use the end command or press Ctrl-Z.

About The Author

harrychanputra.web.id

Number of Entries : 295

Leave a Comment

© 2011 Powered By Wordpress, Goodnews Theme By Geeks Docuementation

Scroll to top